Burger’s Model
Burger’s model simulates creep mechanisms by using a Kelvin model and a Maxwell model connected in series in both the normal and shear directions.
Introduction
The Burger’s model provides a Kelvin model acting in series with a Maxwell model, in both the normal and shear directions. The Kelvin model is the combination of linear spring and dashpot components that act in parallel. The Maxwell model, on the other hand, is the combination of linear spring and dashpot components that act in series. Burger’s model acts over a vanishingly small area, and thus transmits only a force.
Behavior Summary
The rheological components of the Burger’s model are shown in Figure 1 for both the normal and shear directions. In both directions, the model combines Kelvin and Maxwell models acting in series. In the normal direction, the Kelvin model provides a linear spring with stiffness \(K_{k_n}\) and a dashpot with viscosity \(C_{k_n}\), and the Maxwell model provides a linear spring with stiffness \(K_{m_n}\) and a dashpot with viscosity \(C_{m_n}\). The Burger’s model can sustain tensile forces (\(M_t=0\)) or not (\(M_t=1\)). In the shear direction, , the Kelvin model provides a linear spring with stiffness \(K_{k_s}\) and a dashpot with viscosity \(C_{k_s}\), and the Maxwell model provides a linear spring with stiffness \(K_{m_s}\) and a dashpot with viscosity \(C_{m_s}\). A slider with friction coefficient \(f_s\) limits the value of the shear force according to a Coulomb law.
In each direction, the total displacement of the Burger’s model, \(u\), is the sum of the displacement of the Kelvin section (\(u_k\)) and that of the Maxwell section ( \(u_{m_K}\) , \(u_{m_C}\) ) of the model:
The first and second derivatives of the equation above are given by :
The contact forces, \(f\), using the Kelvin section and the first derivative, are given by (3). Note that symbols \(\pm\) and \(\mp\) correspond to the cases of normal and shear direction, respectively (For example, \(\pm\) means \(+\) for normal direction and \(\) for shear direction.).
Also, using stiffness \(K_m\) and viscosity of the Maxwell section:
Using Eqs (2) through (4), the secondorder differential equation for contact force \(f\) is given by:
The force at a given step can be updated based on its value at the previous step and on values of the displacements at the current step and at the previous steps, using a finite dfifference scheme described below.
ActivityDeletion Criteria
A contact with the Burger’s model is active if and only if the contact gap (\(g_{c}\)) is less than or equal to zero. The forcedisplacement law is skipped for inactive contacts.
ForceDisplacement Law
The forcedisplacement law for the Burger’s model updates the contact force and moment:
where \(\mathbf{F}\) combines the contributions from the Kelvin and Maxwell models acting in series. \(\mathbf{F}\) is resolved into normal and shear forces:
where \(F_{n} >0\) is tension. The shear force lies on the contact plane, and is expressed in the contact plane coordinate system:
From the second equation in (3) of the Kelvin section:
By using a central difference approximation of the finite difference scheme for the time derivative and taking average values for \(u_k\) and \(f\):
Therefore,
where:
For the Maxwell section, the displacement and the first derivative are given by:
Substituting the second and fourth equations of (4) into the second equation above:
By using a central difference approximation of the finite difference scheme and taking the average value for \(f\),
Therefore,
The total displacement and the first derivative of the Burger’s model are given by:
By using the finite difference scheme for the time derivative,
Substituting Eqs (11) and (16) into the equation above, the contact force, \(f^{t+1}\), is given by:
Where:
The contact force \(f^{t+1}\) can be calculated from know values for \(u^{t+1}\), \(u^t\), \(u_k^t\) and \(f^t\).
The forcedisplacement law for the Burger’s model consists of the following steps.
Update the normal force \(F_{n}\) according to Eq. (19).
Update the shear force as follows:
Update the shear force \(\mathbf{F}_{s}\) according to Eq. (19).
Compute the shear strength:
(21)\[F_{s}^{*} =  f_s F_{n} .\]Update the linear shear force:
(22)\[\begin{split}\mathbf{F}_{s} = \left\{\begin{array}{l} {\qquad \mathbf{F}_{s} ,\qquad \left\ \mathbf{F}_{s} \right\ \le F_{s}^{*} } \\ {\qquad F_{s}^{*} \left({\mathbf{F}_{s} \mathord{\left/ {\vphantom {\mathbf{F}_{s} \left\ F_{s}^{*} \right\ }} \right.} \left\ \mathbf{F}_{s} \right\ } \right),\qquad {\rm otherwise.}} \end{array}\right.\end{split}\]Update the slip state:
(23)\[\begin{split}s=\left\{\begin{array}{l} {\qquad {\rm true},\qquad \left\ \mathbf{F}_{s} \right\ = F_{s}^{*} } \\ {\qquad {\rm false},\qquad {\rm otherwise.}} \end{array}\right.\end{split}\]If the slip state is true, then the contact is sliding. Whenever the slip states changes, the slip_change callback event occurs.
Energy Partitions
The Burger’s model does not provide any energy partition.
Properties
The properties defined by the Burger’s contact model are listed in the table below as a concise reference; see the Contact Properties section for a description of the information in the table columns.
Keyword 
Symbol 
Description 
Type 
Range 
Default 
Modifiable 
Inheritable 

burger 
Model name 

bur_knk 
\(K_{k_n}\) 
Normal stiffness Kelvin section [force/length] 
FLT 
\([0.0,+\infty)\) 
0.0 
YES 
NO 
bur_cnk 
\(C_{k_n}\) 
Normal viscosity Kelvin section [force×time/length] 
FLT 
\([0.0,+\infty)\) 
0.0 
YES 
NO 
bur_knm 
\(K_{m_n}\) 
Normal stiffness Maxwell section [force/length] 
FLT 
\([0.0,+\infty)\) 
0.0 
YES 
NO 
bur_cnm 
\(C_{m_n}\) 
Normal viscosity Maxwell section [force×time/length] 
FLT 
\([0.0,+\infty)\) 
0.0 
YES 
NO 
bur_ksk 
\(K_{k_s}\) 
Shear stiffness Kelvin section [force/length] 
FLT 
\([0.0,+\infty)\) 
0.0 
YES 
NO 
bur_csk 
\(C_{k_s}\) 
Shear viscosity Kelvin section [force×time/length] 
FLT 
\([0.0,+\infty)\) 
0.0 
YES 
NO 
bur_ksm 
\(K_{m_s}\) 
Shear stiffness Maxwell section [force/length] 
FLT 
\([0.0,+\infty)\) 
0.0 
YES 
NO 
bur_csm 
\(C_{m_s}\) 
Shear viscosity Maxwell section [force×time/length] 
FLT 
\([0.0,+\infty)\) 
0.0 
YES 
NO 
bur_fric 
\(f_s\) 
Friction coefficient [] 
FLT 
\([0.0,+\infty)\) 
0.0 
YES 
NO 
bur_mode 
\(M_t\) 
Normalforce tensile mode [] 
INT 
\(\{0,1\}\) 
0 
YES 
NO 
\(\;\;\;\;\;\;\begin{cases} \mbox{0: with tensile force} \\ \mbox{1: without tensile force} \end{cases}\) 

bur_slip 
\(s\) 
Slip state [] 
BOOL 
{false,true} 
false 
NO 
N/A 
\(\;\;\;\;\;\;\begin{cases} \mbox{true: slipping} \\ \mbox{false: not slipping} \end{cases}\) 

bur_force 
\(\mathbf{F}\) 
Total force (contact plane coord. system) 
VEC 
\(\mathbb{R}^3\) 
\(\mathbf{0}\) 
NO 
NO 
\(\left( F_n,F_{ss},F_{st} \right) \quad \left(\mbox{2D model: } F_{ss} \equiv 0 \right)\) 
Surface Property Inheritance
The Burger’s model does not provide property inheritance capabilities.
Methods
The Burger’s model does not provide any method.
Callback Events
Event 
Array Slot 
Value Type 
Range 
Description 

contact_activated 
Contact has become active 

1 
C_PNT 
N/A 
Contact pointer 

slip_change 
Slip state has changed 

1 
C_PNT 
N/A 
Contact pointer 

2 
INT 
{0,1} 
Slip change mode 

\(\;\;\;\;\;\;\begin{cases} \mbox{0: slip has initiated} \\ \mbox{1: slip has ended} \end{cases}\) 
Usage and Verification Examples
The Verification Problem “Burger’s Contact Model: Stress Relaxation” compares the timedecay of the normal force to the expected analytical solution.
Model Summary
An alphabetical list of the linear model properties is given here.
Was this helpful? ...  Itasca Software © 2024, Itasca  Updated: Sep 26, 2024 