# WIPP Model

An empirical creep law, known as the WIPP-reference creep law, has been developed to describe the time- and temperature-dependent creep of natural rock salt, specifically for nuclear waste isolation studies. The model is described by Herrmann et al. (1980a and b); a different expression of the same creep law is also given by Senseny (1985).

The WIPP-reference creep law, as implemented in FLAC3D, partitions the deviatoric strain-rate tensor, \(\dot\epsilon_{ij}^d\), into elastic and viscous parts (\(\dot\epsilon_{ij}^{de}\) and \(\dot\epsilon_{ij}^{dv}\), respectively):

where the deviatoric strain-rate is obtained:

The elastic part is related to the deviatoric stress-rate,

where \(G\) is the elastic shear modulus, and

The viscous part of the deviatoric strain-rate is coaxial with the deviatoric stress tensor (normalized by its magnitude, \(\bar\sigma\), defined in Equation (9), and is given by

where the scalar strain-rate, \(\dot\epsilon\), is composed of two parts, \(\dot\epsilon_p\) and \(\dot\epsilon_s\), corresponding to primary and secondary creep, respectively,

The formulation for the primary creep rate depends on the magnitude of the secondary creep rate:

The secondary creep rate is

where \(D\), \(n\), \(A\), \(B\), and \(\dot\epsilon_{ss}^*\) are material constants, \(R\) is the universal gas constant, \(Q\) is the activation energy, \(T\) is the temperature in degrees Kelvin, and \(\bar\sigma\) is the von Mises stress:

The volumetric response of the model is purely elastic and is given by

where \(K\) is the bulk modulus.

An iterative approach is used to apply the preceding equations, because the constitutive models in FLAC3D or 3DEC take the components of strain rate as independent variables. A model must supply the new stress tensor, on the assumption of constant strain increments. On the first iteration, the stress components, \(\sigma_{ij}^d\), are taken to be the current ones; creep strain-rates are computed according to Equation (5). New deviatoric stress components, \(\sigma_{ij}^{d'}\), are then computed on the basis of Equations (1), (3), and (5):

where \(\sigma_{ij}^{d^\circ}\) are the stress components that exist on entry to the constitutive model, and \(\Delta t\) is the creep timestep.

On the next and subsequent iterations, the averages of the new and old stress components are used in the creep equations:

Further, the mean primary creep-strain, \(\epsilon_p\), is determined during every iteration:

and used in Equation (13). The quantity \(\epsilon_p^\circ\) is the primary creep-strain on entry to the constitutive model; it is updated on exit:

The WIPP-model notation is summarized and typical values are listed in Table 1.

WIPP notation |
Units |
Typical Value |
---|---|---|

A |
— |
4.56 |

B |
— |
127 |

D |
Pa |
5.79 × 10 |

n |
— |
4.9 |

Q |
cal/mol |
12,000 |

R |
cal/mol K |
1.987 |

\(\dot \epsilon_{ss}^*\) |
s |
5.39 × 10 |

References

Herrmann, W., W.R. Wawersik and H. S. Lauson. Analysis of Steady State Creep of Southeastern New Mexico Bedded Salt, Sandia National Laboratories, SAND80-0558 (1980a).

Herrmann, W., W.R. Wawersik and H. S. Lauson. Creep Curves and Fitting Parameters for Southeastern New Mexico Rock Salt, Sandia National Laboratories, SAND80-0087 (1980b).

Senseny, P.E. “Determination of a Constitutive Law for Salt at Elevated Temperature and Pressure,” American Society for Testing and Materials, Reprint 869 (1985).

Examples

wipp Model Properties

Use the following keywords with the `zone property`

(FLAC3D) or `zone property`

(3DEC) command to set these properties of the WIPP model.

- activation-energy f
activation energy, \(Q\)

- bulk f
bulk modulus, \(K\)

- constant-a f
WIPP model constant, \(A\)

- constant-b f
WIPP model constant, \(B\)

- constant-d f
WIPP model constant, \(D\)

- constant-gas f
gas constant, \(R\)

- creep-rate-critical f
critical steady-state creep rate, \(ε̇ ^*_{ss}\)

- exponent f
WIPP model exponent, \(n\)

- poisson f
Poisson’s ratio, \(v\)

- shear f
shear modulus, \(G\)

- temperature f
zone temperature, \(T\)

- young f
Young’s modulus, \(E\)

- creep-strain-primary f (r)
accumulated primary creep strain, \(ε̇_s\)

- creep-rate-primary f (r)
accumulated primary creep strain rate, \(ε_s\)

**Key**- (r) Read-only property.
This property cannot be set by the user. Instead, it can be listed, plotted, or accessed through FISH.

**Notes**Only one of the two options is required to define the elasticity: bulk modulus \(K\) and shear modulus \(G\), or Young’s modulus \(E\) and Poisson’s ratio \(v\).

The creep behavior is triggered by deviatoric stress, while the volumetric behavior does not consider creep.

Was this helpful? ... | Itasca Software © 2024, Itasca | Updated: Sep 26, 2024 |