Background Images
A sketch set accepts two types of background images: bitmaps (BMP, JPG, PNG, etc.) and geometric data sets (DXF, GEOM, STL). Either may be used as a guide for construction. A bitmap is suitable for tracing, primarily. A geometric data set’s numeric information may be used to automatically create edges conforming to the background geometry (see Creating Edges from Background Geometry in Advanced Edge Operations).
A single sketch set accepts one bitmap and one geometric data set only.
Import a Background Image
Press the Import button () on the toolbar to import a background image into a sketch set. The accepted file types are
Image files (*.bmp *.pbm *.pgm *.png *.ppm *.xbm *.xpm)
DXF files (*.dxf)
Geom files (*.geom)
STL files (*.stl)
When a file is opened, the image will be automatically placed in the construction view.
Select a Background Image
To select a background image, double-click anywhere within its limits using the select tool. When it is selected, it will appear with handle points around it:
An image may also be selected by right-clicking it and choosing the
menu command.Deselect an Image
- Once an image is selected, it may be deselected by:
pressing Esc key,
clicking anywhere outside the bounds of the bitmap rectangle,
selecting a different tool from the toolbar,
right-click the selected image and choose Exit Mode from the context menu.
Move a Background Image
Select the image per above, then drag from within the image (not on one of the handle points).
Resize a Background Image
Select the image per above, then drag a handle point. Aspect ratio is always maintained when resizing, regardless of which handle point is used in the operation. A point that may be used to resize is highlighted in cyan when the mouse is positioned over it. The resize operation will take the point opposite the chosen handle point as an anchor (that is, the fixed point of reference) for the resize operation. See also the next section on pinning a background image.
Pin a Background Bitmap Image
A point of reference for resizing — a pin — may be set by first selecting the background image and then right-clicking it and selecting Set Pin. This will change the mouse cursor to the pin ( ), which can be placed anywhere within the background image by clicking at the desired point. When setting the pin, it is useful to observe the position of the cursor in the status bar. After clicking to set the pin, the image may be resized using it as the anchor.
Using the pin can be part of a process for positioning and sizing a bitmap image which may serve as a reference for your model. The animated figure below shows an example of such process. In this example, the coordinates of the lower left corner, bench floor width and elevation are known, which allows positioning of sketch points at these locations. After that the image is moved and scaled to conform to these locations, and sketch edges are created along the edges of the image.
A pin is only available for use when the background image is selected. When the image is de-selected, the pin is removed.
Rotate a Background Image
To rotate the image, select it and double-click on it again. A rotation circle, as shown below, will indicate that the image can be rotated.
While in this mode, press the mouse left button to grab the image and move the mouse to rotate the image. The rotation angle (from horizontal) can also be set in the Object Properties control set in the Tools area.
Cycling the Edit Modes
Repeatedly double-clicking the image will cycle through these three states: select for re-sizing/repositioning, select for rotation, and deselect.
Snap-To Behavior on Background Geometry
While using the line tool, place the mouse over a geometric data set to highlight the edges and to snap to them. When the mouse is placed over or near a vertex where multiple edges join, they all will be highlighted; clicking the mouse will place a sketch point at the node location.
Pressing the shift key while using the line tool will suspend snap-to behavior until the key is released. Pressing the ctrl key while adding an edge will constrain placement to 15º increments, or, if geometric data is highlighted, to that data.
Snap-to behavior is not available on a bitmap-type background image.
Selection With Two Images in the Sketch
A sketch may contain one pixel-based (bitmap) image and one data-based (geometry) data set. In the event that these overlap, double-clicking within an area of overlap will cause cycling of edit states as follows:
select the bitmap for resizing/repositioning
select the bitmap for rotation
select the geometry for resizing/repositioning
select the geometry for rotation
de-select (remove selection)
Was this helpful? ... | Itasca Software © 2024, Itasca | Updated: Sep 26, 2024 |