# One-way Fluid Coupling

For some problems, it is desirable to use some form of one-way coupling. In one-way coupling, the particles are influenced by the fluid, but the fluid is not influenced by the particles. The CFD module supports this type of modeling. The basic procedure is the following.

Read a fluid mesh.

Set the fluid density and viscosity.

Set the fluid velocity.

Solve or cycle.

## Problem Description

Three particles with radii 1, 1.5 and 2 mm and density 2000 kg/m^{3} settle under gravity in a still fluid with density 1000 kg/m^{3} and viscosity of 1.5 Pa s.

## Analytical Solution

The equation of motion for a spherical particle falling under gravity in a viscous fluid is

where \(g\) is the acceleration due to gravity, \(\rho_p\) and \(f\) are the particle and fluid densities, \(u_z\) is the vertical velocity of the settling particle, and \(C_d\) is the drag coefficient. The drag coefficient, \(C_d\), is a function of the particle Reynolds number.

As the falling ball reaches a steady velocity, \(du_z \over dt\) becomes zero. This allows us to write

It has been shown that for small Reynolds numbers, the drag coefficient is simply ([Batchelor1967])

where \(Re_p\) is the particle Reynolds number defined as

With this definition of \(C_d\), Equation (1) can be solved exactly to give Stokes’ law:

## Implementation

The file `one_way_cfd.p3dat`

listed below drives this example.

```
model new
model large-strain on
model title 'One-way CFD coupling example'
model domain extent -1 2 -1 2 0 2 condition periodic
contact cmat default model linear
model mechanical timestep maximum 1e-5
wall generate name 'cell1' box 0 1 0 1 0 1
wall delete walls range set name 'cell1Bottom'
wall delete walls range set name 'cell1Top'
wall generate name 'cell2' box 0 1 0 1 1 2
wall delete walls range set name 'cell2Bottom'
wall delete walls range set name 'cell2Top'
wall property 'kn' 1e2 'ks' 1e2 'fric' 0.25
model gravity 0 0 -9.81
ball create radius 0.001 position-x 0.5 position-y 0.3 position-z 1.5
ball create radius 0.0015 position-x 0.5 position-y 0.5 position-z 1.5
ball create radius 0.002 position-x 0.5 position-y 0.7 position-z 1.5
ball attribute density 2000.0
ball property 'kn' 1e2 'ks' 1e2 'fric' 0.25
model configure cfd
cfd read nodes 'Node.dat'
cfd read elements 'Elem.dat'
cfd buoyancy on
element cfd attribute density 1000.0
element cfd attribute viscosity 1.5
element cfd attribute velocity-x 0.0
element cfd attribute velocity-y 0.0
element cfd attribute velocity-z 0.0
fish define set_fluid_velocity
loop foreach local ele element.cfd.list
element.cfd.vel.x(ele) = 0.0
element.cfd.vel.y(ele) = 0.0
element.cfd.vel.z(ele) = 0.0
end_loop
end
[set_fluid_velocity]
ball history velocity-z id 1
ball history velocity-z id 2
ball history velocity-z id 3
model cycle 2500
ball list attribute velocity
program return
```

Once the CFD module has been loaded with the command `model configure cfd`

,
the fluid particle interaction forces will be calculated and applied
to the particles.

## Results

The three different particles reach three different terminal velocities. This is expected since the terminal velocity is controlled by a balance between drag forces which are proportional to particle radius squared and gravitational forces which are proportional to particle radius cubed.

The PFC particle terminal velocities are -1.50, -3.33 and -5.86 mm/s. Stokes’ law (5) predicts terminal velocities of -1.45, -3.27 and -5.81 mm/s. PFC predicts slightly higher terminal velocities than Stokes’ law because the drag coefficient formulation used in PFC includes momentum effects.

G.K. Batchelor, An Introduction to Fluid Dynamics. Cambridge University Press, Cambridge. 1967.

Was this helpful? ... | Itasca Software © 2024, Itasca | Updated: Sep 26, 2024 |