Power-Mohr Model: Cylindrical Cavity

Note

To view this project in FLAC3D, use the menu command Help ? Examples…. Choose “Creep/ CylindricalCavityPowerMohr” and select “CylindricalCavityPowerMohr.f3dprj” to load. The project’s main data files are shown at the end of this example.

The problem of radial creep of an infinitely long, thick-walled cylinder, presented in Power Model: Cylindrical Cavity, is analyzed again in this example, this time considering a viscoplastic material. The material viscous behavior is characterized by a single-component power law, and the plastic behavior by a Mohr-Coulomb yield criterion. The plastic properties of the material are associated, the cohesion is 15 MPa, and the friction angle is 15 degrees. The steady-state solution is compared to the analytical solution for a viscoelastic material obeying the same viscous law (see Power Model: Cylindrical Cavity).

The model geometry, material properties, and initial and boundary conditions are the same as those used in Power Model: Cylindrical Cavity. The numerical simulation is performed in three stages. In the first stage, the cohesion is set to a high value and the model is run to elastic equilibrium. In the second stage, the actual values for cohesion, friction, and dilation are assigned to the zones, and the new equilibrium state is calculated. The velocities are reset to zero before performing the creep calculation (stage 3).

The viscoelastic analytical solution is given by the FISH function powcyl, included in the project. The results for radial and hoop stresses and plastic state at the end of the simulation are presented in Figure 1 and Figure 2. As may be observed on the plots, the region around the internal cavity is yielding, and the effect of plasticity translates in a reduction of the hoop stress magnitude in the plastic domain.

Figure 1: Radial and hoop stress at steady state—comparison between viscoplastic solutions (lines) and viscoelastic solutions (symbols).

Figure 2: Plastic state at steady state.

Data File

;------------------------------------------------------------
;       cylindrical cavity -- power-mohr model
;-------------------------------------------------------------------
model new
model largestrain off
fish automatic-create off
model title "Power-Mohr Creep Model --- Cylindrical Cavity"
model configure creep
;
zone create brick  point 0 1 0 0               point 1 20 0 0           ...
                   point 3 0.98769 0.15643 0   point 6 19.754 3.129 0   ...
                   point 2 1 0 -1              point 4 20 0 -1          ...
                   point 5 0.98769 0.15643 -1  point 7 19.754 3.129 -1  ...
                   size 20 1 1  ratio 1.2 1 1
zone face skin
zone cmodel power-mohr
; Properties and stresses in Pascal units (not MPa)
zone property bulk=1e9 shear=3e8
zone property constant-1=1e-25 exponent-1=3
zone property cohesion 1e15 tension 1e15
;
zone gridpoint fix velocity-y range position-y 0
zone gridpoint fix velocity-z range position-y 0
zone face apply velocity-normal 0 range group 'North'
zone face apply velocity-dip    0 range group 'North'
zone face apply stress-normal -100e6 range group 'East'
zone initialize stress xx -100e6 yy -100e6 zz -100e6
;
model save 'cyl_pmini'
model step 2000
model save 'cyl_pm0'
zone property cohesion 1.5e7 friction 15 dilation 15 tension 1e15
model step 2000
model save 'cyl_pm1'
;
model history mechanical unbalanced-maximum
zone history velocity-x gridpointid 1
zone history velocity-x gridpointid 81
zone history displacement-x gridpointid 1
zone history displacement-x gridpointid 81
zone history stress-xx gridpointid 1
zone history stress-yy gridpointid 1
zone history stress-zz gridpointid 1
model history creep time-total
model history timestep
;
zone gridpoint initialize velocity (0,0,0)
model creep active on
model creep timestep starting 1.0e-5
model creep timestep minimum 1.0e-5
model creep timestep maximum 1.0
model solve time-total 4000
model save 'cyl_pm2'
; compare analytic solution......
call 'solution' suppress 
table  1 label 'Flac3d x-velocity'
table 11 label 'Analytical x-velocity'
table  2 label 'Flac3d radial stress'
table 12 label 'Analytical radial stress'
table  3 label 'Flac3d hoop stress'
table 13 label 'Analytical hoop stress'
table  4 label 'Flac3d out-of-plane stress'
table 14 label 'Analytical out-of-plane stress'
model save 'cylindrical-cavity-powermohr'
return