3DEC 5.2 to 7.0 Command Mapping
This document lists 3DEC 5.2 commands and provides links to their 3DEC 7.0 counterparts.
3DEC 5.2 | 3DEC 7.0 |
---|---|
APPLY thermal convection | block face apply convection |
APPLY thermal flux | block face apply flux |
APPLY thermal psource | block gridpoint apply source |
APPLY thermal temp | block gridpoint apply temperature |
APPLY thermal vsource | block zone apply source |
APPLY xvel | block apply velocity-x |
APPLY yvel | block apply velocity-y |
APPLY zvel | block apply velocity-z |
BOUNDARY added_mass | block face apply westergaard |
BOUNDARY discharge | flowplane edge apply discharge |
BOUNDARY fluidpropconc | flowknot apply proppant-volume |
BOUNDARY fluidtemp | flowknot apply temperature |
BOUNDARY flux | flowplane edge apply flux |
BOUNDARY kndis | flowknot apply discharge |
BOUNDARY knflux | flowknot apply flux |
BOUNDARY nvelocity | block gridpoint apply velocity-normal |
BOUNDARY ppressure | flowknot apply pore-pressure |
BOUNDARY principal | block face apply stress-principal |
BOUNDARY reaction | block gridpoint apply reaction |
BOUNDARY stress | block face apply stress |
BOUNDARY xfree | block face apply-remove |
BOUNDARY xload | block gridpoint apply force-x |
BOUNDARY xtraction | block face apply stress-xx |
BOUNDARY xvelocity | block gridpoint apply velocity-x |
BOUNDARY xvisc | block gridpoint apply viscous-x |
BOUNDARY yfree | block face apply-remove |
BOUNDARY yload | block gridpoint apply force-y |
BOUNDARY ytraction | block face apply stress-yy |
BOUNDARY yvelocity | block gridpoint apply velocity-y |
BOUNDARY yvisc | block gridpoint apply viscous-y |
BOUNDARY zfree | block face apply-remove |
BOUNDARY zload | block gridpoint apply force-z |
BOUNDARY ztraction | block face apply stress-zz |
BOUNDARY zvelocity | block gridpoint apply velocity-z |
BOUNDARY zvisc | block gridpoint apply viscous-z |
CALL | program call |
CAVE | no equivalent (not supported) |
CHANGE cable | sel cable node change , sel cable change |
CHANGE cons | block zone cmodel assign |
CHANGE dfn | block contact cmodel assign , block contact prop . Use range dfn-3dec. |
CHANGE jcons | block contact jmodel assign |
CHANGE jmat | block contact property |
CHANGE mat | block zone property |
CHANGE wall | block makewall |
CONFIG array | model configure array |
CONFIG cppfish | model configure plugin |
CONFIG cppudm | model configure plugin |
CONFIG creep | model configure creep |
CONFIG dynamic | model configure dynamic |
CONFIG energy | model configure energy |
CONFIG feblock | model configure feblock |
CONFIG fluid | model configure fluid |
CONFIG highorder | model configure highorder |
CONFIG lhs | no equivalent (not supported) |
CONFIG liner | no equivalent (always configured |
CONFIG matrixflow | model configure matrixflow |
CONFIG thermal | model configure thermal |
CONTINUE | program continue |
COUPLE | no equivalent (not supported) |
CYCLE | model cycle |
DAMPING | block mechanical damping |
DEFINE … END | fish define and end (note end is a statement, not a command, so it is not preceded by fish) |
DELETE | block delete |
DENSIFY | block densify |
DFN addfracture | fracture create |
DFN cluster | fracture cluster |
DFN combine | fracture combine |
DFN connectivity | fracture connectivity |
DFN copy | fracture copy from-dfn |
DFN delete | fracture delete |
DFN export | fracture export |
DFN extra | fracture extra and fracture dfn-extra |
DFN generate | fracture generate |
DFN gimport | fracture import from-geometry |
DFN group | fracture group and fracture dfn-group |
DFN import | fracture import |
DFN information | fracture verify-file |
DFN intersection | fracture intersections compute and fracture intersections delete |
DFN property | fracture property |
DFN prune | fracture prune |
DFN template | fracture template create and fracture template delete |
DFN traces | fracture intersection scanlines |
DOMAIN | model domain |
DUMP | block list dump (deprecated) |
DYNAMIC | block dynamic eigen |
EXCAVATE | block excavate |
ECHO | program echo-line |
EXIT | program exit |
FACETRIANGLE | block face triangulate |
FFIELD | block dynamic free-field |
FILL | block fill |
FIND | block hide (use block hide off to find) |
FISH debug | fish debug |
FISH initialize | no equivalent |
FIX xrot | block fix rotation-x |
FIX xvel | block fix velocity-x |
FIX yrot | block fix rotation-y |
FIX yvel | block fix velocity-y |
FIX zrot | block fix rotation-z |
FIX zvel | block fix velocity-z |
FLUID add_proppant | block fluid proppant active |
FLUID aper_f | flowplane property f-factor |
FLUID area_min | flowplane zone area-minimum |
FLUID bulk | block fluid property bulk |
FLUID bulk_joint | block fluid property bulk |
FLUID bulk_matrix | block fluid property bulk-matrix |
FLUID cohwater | block fluid property cohesion |
FLUID density | block fluid property density |
FLUID do_proppant_settling | block fluid proppant settling |
FLUID empa | flowplane property a-factor |
FLUID empb | flowplane property b-factor |
FLUID expa | flowplane property a-factor |
FLUID fhide | flowplane hide |
FLUID fht_coe | block fluid property heat-transfer-coefficient |
FLUID flow_edge_min | flowplane zone edge-minimum |
FLUID fseek | flowplane hide . (use flowplane hide off to find) |
FLUID fspec_heat | block fluid property specific-heat |
FLUID fth_cond | block fluid property thermal-conductivity |
FLUID gas_alpha | block fluid gas alpha |
FLUID gas_bulkmin | block fluid gas bulk-minimum |
FLUID gas_constant | block fluid gas constant |
FLUID gas_densitymin | block fluid gas density-minimum |
FLUID proppant_blocked_permmult | block fluid proppant permeability-factor |
FLUID proppant_density | block fluid proppant density |
FLUID proppant_grain_size_factor | block fluid proppant grain-size-factor |
FLUID viscosity | block fluid property viscosity |
FLUID volmin | flowplane zone volume-minimum |
FRACTION | model mechanical timestep safety-factor |
FRAGMENT | block fragment |
FREE | block free |
GENERATE | block zone generate |
GEOMETRY copy | geometry copy |
GEOMETRY edge | geometry edge create |
GEOMETRY export | geometry export |
GEOMETRY group | geometry assign-groups |
GEOMETRY import | geometry import |
GEOMETRY node | geometry node create |
GEOMETRY paint | geometry paint |
GEOMETRY polygon | geometry polygon create |
GEOMETRY remove | geometry polygon delete , geometry edge delete , geometry node delete |
GEOMETRY set | geometry select |
GRAVITY | model gravity |
GRID | block thermal grid |
GROUP block (et al.) | grouping is a facility (keyword) within other commands; see, for instance, block group , sel cable group , flowknot group , etc. |
GUI | project save |
HEADING | model title |
HELP | help |
HIDE | block hide |
HISTORY s1 (et al.) | Adding a history on an object is done through the object; for instance, block history or block contact history or fish history , etc. Histories at gridpoints are done using the gridpointid or position keywords in the block history command. |
HISTORY crtdel | model history timestep |
HISTORY crtime | model history creep time-total |
HISTORY damping | model history damping |
HISTORY energy | model history energy |
HISTORY fltime | model history fluid time-total |
HISTORY thtime | model history thermal time-total |
HISTORY ratio | model history mechanical ratio |
HISTORY unbalanced | model history mechanical unbalanced-maximum |
HISTORY delete | history delete |
HISTORY dump | history list series |
HISTORY hist_rep | history interval |
HISTORY label | history.name a label (see history name label ) |
HISTORY limits | history list limit |
HISTORY list | history list series |
HISTORY ncycle | history interval |
HISTORY nstep | history interval |
HISTORY purge | history purge |
HISTORY reset | history delete |
HISTORY write | history list series |
INITEMPERATURE | block gridpoint initialize temperature-analytical |
INITIALIZE fluid proppant_volume_fraction | flowplane vertex initialize proppant-volume |
INITIALIZE fluid proppant_limit_volume_fraction | block fluid proppant concentration-limit-volume |
INITIALIZE fluid proppant_confined_modulus | block fluid proppant modulus |
INITIALIZE fluid proppant_grain_size | block fluid proppant grain-size |
INITIALIZE fluid proppant_permeability | block fluid proppant permeability |
INITIALIZE gpp | block gridpoint initialize pore-pressure |
INITIALIZE sxx | block zone initialize stress-xx |
INITIALIZE sxy | block zone initialize stress-xy |
INITIALIZE sxz | block zone initialize stress-xz |
INITIALIZE syy | block zone initialize stress-yy |
INITIALIZE syz | block zone initialize stress-yz |
INITIALIZE szz | block zone initialize stress-zz |
INITIALIZE temperature | block gridpoint initialize temperature |
INITIALIZE xdisplacement | block gridpoint initialize displacement-x |
INITIALIZE xvelocity | block gridpoint initialize velocity-x |
INITIALIZE ydisplacement | block gridpoint initialize displacement-y |
INITIALIZE yvelocity | block gridpoint initialize velocity-y |
INITIALIZE zdisplacement | block gridpoint initialize displacement-z |
INITIALIZE zvelocity | block gridpoint initialize velocity-z |
INSITU | block insitu |
ISOTHERMAL | block thermal isothermal |
JMODEL model | block contact jmodel |
JMODEL | block contact property |
JOIN | block join |
JOIN_CONTACT | block contact join |
JSET | block cut joint-set |
LABEL arrow | data label create arrow |
LABEL delete | data label delete |
LABEL end | data label create end |
LABEL text | data label create text |
LABEL x y z | data label create position |
the four above optionally take an index with the id keyword (i.e. LABEL id 1 arrow) |
in which case the corresponding translation is data label create name "1" arrow where the index is now a string (that may be a numeral) |
LINE | block thermal line |
LIST apply | block list apply |
LIST at | block list at |
LIST axial | sel reinforcement list |
LIST b_max | block list limits |
LIST bad3 | block face list bad-edge |
LIST badface | block face list bad-normal |
LIST beam | sel beam list |
LIST blist | block list contacts |
LIST block | block list |
LIST boundary | block gridpoint list apply |
LIST brick | block list brick |
LIST cable | sel cable list |
LIST cave | No longer supported |
LIST cell | block list cell |
LIST concave | block list concave |
LIST contact | block contact list |
LIST couple | No longer supported |
LIST cp | block contact list common-plane |
LIST creep | model creep list |
LIST dfn | fracture list |
LIST directory | program list directory |
LIST displacement | block list profile |
LIST domain | model list domain |
LIST energy | block list energy |
LIST face | block face list |
LIST fcheck | block face list check |
LIST feblock | block finite-element list |
LIST fedge | flowplane edge list |
LIST ffield | block dynamic free-field list |
LIST fish | fish list |
LIST fknot | flowknot list |
LIST flaw | block list flaw |
LIST flowrate | flowplane list discharge |
LIST flowvel | flowplane list velocity |
LIST fluid | block fluid list |
LIST fos | model factor-of-safety list |
LIST fpipe | flowplane pipe list |
LIST fplane | flowplane list |
LIST fzone | flowplane zone list |
LIST geometry | geometry list |
LIST globals | model list information |
LIST gridpoint | block gridpoint list |
LIST group | group list |
LIST heat | block thermal list heat |
LIST history | history list |
LIST information | program list information |
LIST jmodel | block contact jmodel list |
LIST jmtable | block contact list material-table |
LIST junk | block list junk (deprecated) |
LIST keyinfo | program list key-information |
LIST label | data label list |
LIST lg | block gridpoint list join |
LIST liner | sel liner list |
LIST master | block list master |
LIST maxima | block list maxima |
LIST mechanical | model mechanical list |
LIST memory | block list memory |
LIST model | program list plugins |
LIST polyhedra | block list polyhedra |
LIST principal | program list principal |
LIST property | Give name of object to get property, e.g. sel beam list property |
LIST proppant | block fluid proppant list |
LIST pstress | block list profile (not working yet) |
LIST range | model list range |
LIST record | model list record |
LIST rface | block face list Use keyword rigid to print out original block faces |
LIST scalar | data scalar list |
LIST security | program list security |
LIST serial | program list serial |
LIST slave | block list slave |
LIST state | model list information |
LIST stress | block list profile (not working yet) |
LIST structure | sel liner list (not working yet) |
LIST table 1 | table "1" list (see table list ) |
LIST temp | block gridpoint list temperature |
LIST tensor | data tensor list |
LIST thermal | model thermal list |
LIST tknot | flowknot list thermal |
LIST trace | trace list |
LIST unbalanced | block list unbalanced |
LIST vector | data vector list |
LIST version | program list version |
LIST vertex | block gridpoint list |
LIST wall | block list information Use range wall to show only wall blocks. |
LIST water | block list water |
LIST zdr | block zone list statistics (deprecated) |
LIST zmax | block zone list ratio |
LIST zone | block zone list |
LOAD | program load |
program mail |
|
MARK | No longer suppporetd. Use block group or block face group |
MSCALE | block mechanical mass-scale |
NEW | model new |
PAUSE | program pause |
PFIX | block contact apply pore-pressure |
POINT | block thermal point |
POLYHEDRON | block create |
PROPERTY | No longer supported. Use block zone property and block contact property |
QUIT | program quit |
RANGE | model range |
REMOVE | No longer supported. Use block excavate |
RESET damp | block mechanical damping |
RESET displacement | block gridpoint initialize displacement |
RESET dxf | No longer supported |
RESET history | history purge |
RESET jdisplacement | block contact reset displacement |
RESET jenergy | block contact reset energy |
RESET jstress | block contact reset stress |
RESET stress | block zone stress initialize |
RESET time | model mechanical time-total |
RESET velocity | block gridpoint initialize velocity |
RESTORE | model restore |
RETURN | program return |
SAVE | model save |
SCALAR | data scalar |
SEEK | block hide Use the keyword off to show blocks. |
SET arcmin | block contact area-minimum |
SET atol | block tolerance |
SET aunb | Specify unbalanced-average limit in the model solve command |
SET case_sensitivity | No longer supported |
SET convection | block thermal convection |
SET crack_flow | block fluid crack-flow |
SET crdt | model creep timestep starting or model creep timestep fix |
SET creeptime | model creep time-total |
SET ctol | block contact tolerance |
SET cust1 | program customer-title-1 |
SET cust2 | program customer-title-2 |
SET cy | No longer supported |
SET damp | block mechanical damping |
SET datum | Set datum in plot item attributes |
SET deterministic | model deterministic |
SET directory | program directory custom |
SET dt | model mechanical timestep maximum |
SET dxf | No longer supported |
SET dynamic | model dynamic active |
SET echo | program echo |
SET edge | block tolerance edge |
SET energy | block mechanical energy active |
SET fastflow | block fluid fastflow |
SET fdtmax | model fluid timestep maximum |
SET fish autocreate | fish automatic-create |
SET fish call | fish callback add |
SET fish case_sensitivity | No longer supported |
SET fish remove | fish callback remove |
SET fish_delete_check | block contact safe-delete |
SET flow | model fluid active |
SET fobl | model creep timestep lower-bound Note - this is now given as a ratio |
SET fobu | Command is ambiguous. Could be model creep timestep upper-bound or model fluid timestep upper-bound |
SET fpcoef | block fluid fastflow-relaxation |
SET gasflow | block fluid gas active |
SET hist_rep | history interval |
SET htol | block tolerance planarity |
SET jcondf | Material numbers no longer supported. Use block contact material-table |
SET jmatdf | Material numbers no longer supported. Use block contact material-table |
SET jmtable | Material numbers no longer supported. Use block contact material-table |
SET join_contact | block contact join-by-contact |
SET jointid | block cut set minimum-id |
SET jplane | block joint-plane |
SET latency | model creep timestep latency |
SET lmul | model creep timestep lower-multiplier |
SET log | program log on |
SET logfile | program log-file |
SET matrix_flow | block fluid matrix-flow |
SET max_cells | block cells size |
SET maxdt | model creep timestep maximum |
SET mech | model mechanical active |
SET min_ang | block tolerance angle |
SET mindt | model creep timestep minimum |
SET munb | Specify unbalanced-maximum limit in the model solve command |
SET ncyc | history interval |
SET ngw | model fluid substep |
SET nmatrix | block fluid jontflow-substep |
SET nmech | model mechanical substep |
SET nodal | block zone nodal-mixed-discretization |
SET notice | program notice on |
SET nproppant | No longer supported |
SET nstep | history interval |
SET nther | model thermal substep |
SET nucp | block update common-plane |
SET nucx | block update subcontact |
SET nup_cab | sel cable update |
SET nup_fluid_timestep | block fluid timestep-update |
SET nupdt | block mechanical timestep-update |
SET nupface | block update face-normal |
SET overlay | No longer supported |
SET pagination | program pagination |
SET plotinterval | model update-interval |
SET proc | program threads |
SET random | model random |
SET sdel | block contact delete-open |
SET seed | model random |
SET skip_join_update | block skip-join-update |
SET small | model large-strain Use the keywork off to set small strain. |
SET spface | block cut set split-face |
SET sublist_multi_contact | block contact multi |
SET sync_creep_mech | No longer supported. Mechanical and creep always synced. |
SET tension | No longer supported |
SET th_implicit | block thermal implicit |
SET th_numerical | block thermal analytical Use the keywork off to set numerical solution (this is the default). |
SET th_scale on | block thermal mass-scale |
SET th_store_matrix | No longer supported. Thermal matrix is always stored. |
SET th_time | model thermal time-total |
SET thcoupl | block thermal analytical substep |
SET thdt | model thermal timestep fix |
SET thermal | model thermal active |
SET thtolerance | block thermal tolerance |
SET time | model mechanical time-total |
SET tunnel_axis | Specify tunnel axis when using sel liner list |
SET umul | model creep timestep upper-multiplier |
SET warning | program warning |
SET zvol_del | block zone volume-minimum-delete |
SET zvol_nodal | block zone nodal-mixed-discretization Use the volume-minimum keyword to set the minimum volume. |
SET zvol_ratio | block zone nodal-mixed-discretization Use the volume-minimum-ratio keyword to set the minimum volume ratio. |
SHOW | block hide use the keyword off to show blocks. |
SOLVE | model solve |
SOLVE fos | model factor-of-safety |
SOURCE | block thermal source |
STEP | model step |
STOP | program stop |
STRUCTURE axial | sel reinforcement create |
STRUCTURE beam | struct beam |
STRUCTURE cable | struct cable or sel hybrid |
STRUCTURE delete axial | sel reinforcement delete |
STRUCTURE delete beam | struct beam delete |
STRUCTURE delete cable | struct cable delete or sel hybrid delete |
STRUCTURE delete liner | struct liner delete |
STRUCTURE liner | struct liner |
STRUCTURE property | Properties are specified with the type of element, e.g. sel cable property |
SYMMETRY | block thermal symmetry-planes |
SYSTEM | program system |
TABLE | table add (and associated commands) |
TENSOR | data tensor create (and associated commands) |
THSOLVE | block thermal analytical solve |
TIME | block thermal analytical solve Use time keyword to specify time. |
TITLE | model title |
TRACE add | block trace or block gridpoint trace |
TRACE | trace |
TUNNEL | block cut tunnel |
UNDO | program undo |
VECTOR | data vector create (and associated commands) |
WATER | block water |
ZONE density | block zone property density |
ZONE list | block zone list |
ZONE load | block zone cmodel load |
ZONE model | block zone cmodel assign |
ZONE permeability | block zone fluid property permeability |
ZONE porosity | block zone fluid property porosity |
ZONE … | block zone property |
Was this helpful? ... | PFC © 2021, Itasca | Updated: Feb 25, 2024 |