Examples Index
This index organizes the examples in this documentation by code, and by example type.
- Tutorials are intended to be the first stop for the novice user; they illustrate program features and principles.
- Verification Problems are used to show the validity of program results against the underlying theory; they are not necessarily “real-world” examples.
- Example Applications are full-scale demonstrations of some of the possible uses of the codes.
PFC Examples
This section contains a number of examples detailing PFC usage.
For specific details of the PFC model components (e.g., balls, clumps, walls, and contacts), see PFC.
cs: outdated; restore if updated: Experienced |pfc4| users should first read the “:ref:-experienced_users-” section.
- Tutorials
- Verification Problems
- Measure Logic
- Strength of a Face-Centered Cubic Array of Spheres
- Tip-Loaded Cantilever Beam
- Linear Contact Model: Calibrating the Normal Critical Damping Ratio
- Hertz Contact Model: Complex Loading Paths
- Wave Propagation in Particle Assemblies
- Rolling Resistance Linear Contact Model: Single Ball on a Flat Surface
- Rolling Resistance Linear Contact Model: Repose Angle
- Adhesive Rolling Resistance Linear Contact Model: Repose Angle
- Burger’s Contact Model: Stress Relaxation
- Sliding Wedge
- Example Applications
- Hopper Flow
- Probing a Granular Specimen
- Ribbon Blender
- Fragmentation Analysis during a Uniaxial Compression with Crack Tracking Using Fractures
- DFN Generation, Analysis, and Simplification
- Rock Testing
- Rigid Block Model of Flying Buttresses
- Rigid Block Model of a Rockslide
- Genesis and Testing of a Soft-Bonded Material
- Simple Rigid Block Bonded-Block Modeling (BBM)
- Rigid Block Model of Tunnel Excavation
FLAC3D Examples
This section contains a number of examples detailing FLAC3D usage. For specific details of the FLAC3D model components (e.g., zones and structural elements), see FLAC3D.
- Tutorials
- Example Applications
- Influence of Slope Curvature on Stability
- Pillar Loads at Intersecting Tunnels
- Excavation in a Saturated Soil
- Excavation and Support for a Shallow Tunnel
- Grid Generation for Intersecting Tunnels
- Pressurized Cylindrical Cavern
- Prediction of Borehole Closure in a Salt Formation
- Axial and Lateral Loading of a Concrete Pile
- Undrained Cylindrical Cavity Expansion in a Cam-Clay Medium
- Simulation of Pull-Tests for Fully Bonded Rock Reinforcement
- Wheel Load over a Buried Pipe
- Embankment Loading on a Cam-Clay Foundation
- Impermeable Concrete Caisson Wall with Pretensioned Tiebacks
- Dewatered Construction of a Braced Excavation
- Installation of a Triple-Anchored Excavation Wall
- Reinforced Tunnel Excavation
- Subsidence above Horizontal Cut
- Punch Indentation of a Bonded Material
- Sleeved Triaxial Test of a Bonded Material
- Verification Problems
- Cylindrical Hole in an Infinite Mohr-Coulomb Material
- Cylindrical Hole in an Infinite Hoek-Brown Medium
- Rough Strip Footing on a Cohesive Frictionless Material
- Smooth Circular Footing on an Associated Mohr-Coulomb Material
- Smooth Square Footing on a Cohesive Frictionless Material
- Uniaxial Compressive Strength of a Jointed Material Sample
- Drained and Undrained Triaxial Compression Test on a Cam-Clay Sample
- Lined Circular Tunnel in an Elastic Medium with Anisotropic Stresses
- Development of Plastic Hinges in a Statically Loaded Beam
- Simply Supported Isotropic Rectangular Plate under Combined Lateral and Direct Loads
- Simply Supported Orthotropic Plate
- Cylindrical Concrete Vault
- Free Vibration of a Cantilever Beam
- Simple Slope in Hoek-Brown Material
PFC-FLAC3D Coupling Examples
This section contains a number of examples detailing PFC-FLAC3D coupling usage. For specific details of the PFC-FLAC3D coupling schemes, see Coupling PFC and FLAC3D.
Was this helpful? ... | PFC 6.0 © 2019, Itasca | Updated: Nov 19, 2021 |